D-STIKE Deauther Watch V3 Wearable Deauther Watch ESP8266 Development Board 2.4GHz 3D Printed Case

Wishcolor DSTIKE Deauther Watch V3 Wearable Deauther Watch ESP8266 Development Board 2.4GHz 3D Printed Case

What is it?

Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.

It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.

Please note that the ESP8266 does only support 2.4GHz.

You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.

Function:

Deauther Attack: Disconnect 2.4G WiFi

Deauther Beacon: Create fake networks

Deauther Probe: Confuse WiFi trackers

Packet Monitor: Display WiFi traffic

Clock: Real Time Clock Adjustable

Laser: Powerful Laser can reach 50-100m

GPIOs and Hardware info:

Display: SH1106 1.3" OLED

Display SDA: GPIO 5

Display SCL/SCK: GPIO 4

WS2812b LED: GPIO 15

Button Up: GPIO 12

Button Down: GPIO 13

Button Select: GPIO 14

Laser: GPIO 16

Side Button: GPIO0, RST

What makes it special?

Only ~80mA power usage

800 mA charging current

Up to around 8-10 hours work time

Acrylic cover and 3D print transparent case

Powerful laser for fun

Indicate charging LED (25%，50%，75%，100%)

Included 5dB FPC antenna

Power Switch (Click to turn on, double click to turn off, long click to open flashlight)

Protection: short, overcharging, over discharging, temperature

Added Extremely Accurate DS3231

Package Included:

– 1 x Set of DSTIKE Deauther Watch V3

Disclaimer:

This project is a proof of concept for testing and educational purposes. Neither the ESP8266, nor its SDK was meant or built for such purposes. Bugs can occur!

Use it only against your own networks and devices! Please check the legal regulations in your country before using it. We don't take any responsibility for what you do with this program.

More Info:

Deauth:

Closes the connection of WiFi devices by sending deauthentication frames to access points and client devices you selected. This is only possible because a lot of devices don't use the 802.11w-2009 standard that offers a protection against this attack. Please only select one target! When you select multiple targets that run on different channels and start the attack, it will quickly switch between those channels and you have no chance to reconnect to the access point that hosts this web interface.

Beacon:

Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.

Probe:

Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It's unlikely you will see any impact by this attack with your home network.

Videos:

Software 2.6.0 Introduction: https://www.youtube.com/watch?v=TMvpJiE8Yy8

DSTIKE Deauther Watch V3 Quick Video: https://youtu.be/T7YqPOoR0zc

How do I assemble Deauther watch V3: https://youtu.be/9VLsQ8tLtmE

How to install antenna of Deauther watch: https://youtu.be/JJTnT9NM6Qg

How to increase the maximum effect of antenna: https://youtu.be/PZvyq5-3-bY

How to connect smart phone: https://youtu.be/YpCH9FgOR9w

DSTIKE Deauther Watch Demo: https://youtu.be/9zA6AB7qYe8

NTP Time server functions: https://youtu.be/m4BKdPXVOYM

How to install DSTIKE for Arduino environment: https://youtu.be/wYPD3j6Pk7U

How to use 8266 flash tool flash Deauther firmware: https://youtu.be/MxukE5ZsBSk